i-manager Publications

Corrosion Behavior of AA2014/SiC Metal Matrix Composite Fabricated by Stir Casting Process

Shashi Prakash Dwivedi*, Anand Sharma**, Shashank Pratap Rao***, Sumit Bahuguna****

* Assistant Professor, Noida Institute of Engineering and Technology, Greater Noida, Uttar Pradesh, India.

**-**** B.Tech Graduate, Noida Institute of Engineering and Technology, Greater Noida, Uttar Pradesh, India.

Periodicity:October - December'2016
DOI : https://doi.org/10.26634/jms.4.3.8240

Abstract

The objective of the work is to predict the Corrosion behavior of AA2014 reinforced with SiC with different percent of reinforcement. Effects of the weight fraction of SiC particulates on the corrosion behavior of Al/SiC Metal Matrix Composites (MMCs) were studied. The results revealed that the Al/SiC MMCs exhibited higher density than pure Al matrix. The static immersion corrosion tests of Al/SiC MMCs in 3.5 wt.% NaCl aqueous solution at exposure time 24 hours, 48 hours and 72 hours was carried out. Results showed that the Al/15% SiC MMCs have better corrosion resistance than the pure Al matrix. Increasing the weight fraction of the SiC particulates reduces the corrosion rate of the Al/SiC MMCs.

Keywords

Corrosion, Al/SiC, Matrix, Composites, NaCl.

How to Cite this Article?

Dwivedi, S.P., Sharma, A., Rao, S. P., and Bahuguna, S. (2016). Corrosion Behavior of AA2014/SiC Metal Matrix Composite Fabricated by Stir Casting Process. i-manager’s Journal on Material Science, 4(3), 1-6. https://doi.org/10.26634/jms.4.3.8240

References

[1]. Vignesh. V. Shanbhag, Nitin. N. Yalamoori, S. Karthikeyan, R. Ramanujam and K. Venkatesan, (2014). “Fabrication, Surface Morphology and Corrosion Investigation of Al 7075-Al₂O₃ Matrix Composite in Sea Water and Industrial Environment”. Procedia Engineering, Vol. 97, pp. 607–613.

[2]. V. Auradi, Rajesh G.L, and S. A. Kori, (2014). “Processing of B4C Particulate Reinforced 6061 Aluminum Matrix Composites by Melt Stirring involving two-step Addition”. Procedia Materials Science, Vol. 6, pp. 1068–1076.

[3]. Pardeep Sharma, Satpal Sharma, and Dinesh Khanduja, (2015). “Production and some Properties of Si N 3 4 Reinforced Aluminum Alloy Composites”. Journal of Asian Ceramic Societies, Vol. 3, pp. 352–359.

[4]. R. Senthilkumar, N. Arunkumar, and M. Manzoor Hussian, (2015). “A Comparative Study on Low Cycle Fatigue Behaviour of Nano and Micro Al₂O₃ Reinforced AA2014 Particulate Hybrid Composites”. Results in Physics, Vol. 5. pp. 273-280.

[5]. H.M. Zakaria, (2014). “Microstructural and corrosion behavior of Al/SiC metal matrix composites”. Ain Shams Engineering Journal, Vol. 5, No. 3, pp. 831-838.

[6]. Gopinath K, Balasubramaniam R, and Murthy VSR, (2001). “Corrosion Behavior of Cast Al–Al₂O₃ Particulate Composites”. J Mater Sci Lett, Vol. 20, pp. 793–798

[7]. Hassan Adel M, Abdalla Alrashdan Ahmad TM, and Hayajneh Mohammed T, (2008). “Wear Behavior of Al Cu and Al–Cu/SiC Components Produced by Powder Metallurgy”. J Mater Sci, Vol. 43, pp. 5368–5375.

[8]. Veeresh Kumar GB, Rao CSP, and Selvaraj N, (2011). “Mechanical and Tribological Behavior of Particulate Reinforced Aluminum Metal Matrix Composites–A Review”. J Miner Mater Charact Eng, Vol. 10, No. 1, pp. 59–91.

[9]. S. P. Dwivedi, Sudhir Kumar, and Ajay Kumar, (2012). “Effect of Turning Parameters on Surface Roughness of A356/5% SiC Composite Produced by Electromagnetic Stir Casting”. Journal of Mechanical Science and Technology, Vol. 26 No. 12, pp. 3973-3979.

[10]. Shashi Prakash Dwivedi, Satpal Sharma, and Raghvendra Kumar Mishra, (2014). “Microstructure and Mechanical Properties of A356/SiC Composites Fabricated by Electromagnetic Stir Casting”. Procedia Materials Science, Vol. 6, pp. 1524–1532.

[11]. Shashi Prakash Dwivedi, Satpal Sharma, and Raghvendra Kumar Mishra, (2015). “Microstructure and Mechanical Behavior of A356/SiC/Fly-ash Hybrid Composites Produced by Electromagnetic Stir Casting”. J Braz. Soc. Mech. Sci. Eng., Vol. 37, pp. 57–67.

[12]. Shashi Prakash Dwivedi, Satpal Sharma, and Raghvendra Kumar Mishra, (2014). “A356 Aluminum Alloy and Applications–A Review ”. Advance Materials Manufacturing and Characterization, Vol. 4, No. 2, pp. 81- 86.

[13]. Shashi Prakash Dwivedi, Satpal Sharma, and Raghvendra Kumar Mishra, (2014). “Effects of Roller Burnishing Process Parameters on Surface Roughness of A356/5% SiC Composite using Response Surface Methodology”. Adv. Manuf., Vol. 2, pp. 303–317.

[14]. Shashi Prakash Dwivedi, Satpal Sharma, and Raghvendra Kumar Mishra, (2014). “Electromagnetic Stir Casting and its Process Parameters for the Fabrication and Refined the Grain Structure of Metal Matrix Composites–A Review”. International Journal of Advance Research and Innovation, ISSN 2347–3258, Vol. 2, No. 3, pp. 639-649.

[15]. Shashi Prakash Dwivedi, Sudhir Kumar, and Ajay Kumar, (2014). “Effects of Turning Parameters on Dimensional Deviation of A356/5% SiC Composite using Box-Behnken Design and Genetic Algorithm”. Frontiers in Manufacturing Engineering, Vol. 2, No. 1, pp. 8-14. DOI: 10.7508/FME-V2-N1-8-14

Corrosion Behavior of AA2014/SiC Metal Matrix Composite Fabricated by Stir Casting Process

Abstract

Keywords

How to Cite this Article?

References

If you have access to this article please login to view the article or kindly login to purchase the article

Purchase Instant Access

Options for accessing this content:

	North Americas,UK, Middle East,Europe		India	Rest of world
	USD	EUR	INR	USD-ROW
Pdf	35	35	200	20
Online	35	35	200	15
Pdf & Online	35	35	400	25