References
[1]. Albina, D.O., (2005). “Theory and Experience on
Corrosion of Water wall and Super heater Tubes of Waste-To-
Energy Facilities”. (Master Thesis), Columbia University.
[2]. Deuerling, C., Maguhn, J., Nordsieck, H., Benker, B.,
Zimmermann, R., and Warnecke, R., (2009). “Investigation
of the Mechanisms of Heat Exchanger Corrosion in a
Municipal Waste Incineration Plant by Analysis of the Raw
Gas and Variation of Operating Parameters”. Heat Transf.
Eng., Vol. 30(10-11), pp.822-831.
[3]. Eliaz, N., Shemesh, G., and Latanision, R. M., (2002).
“Hot Corrosion in Gas Turbine Components”. Eng. Fail.
Anal., Vol. 9, pp. 31-43.
[4]. Hancock, P., (1987). “Vanadic and Chloride Attack of
Super alloys”. Mater. Sci. Technol., Vol. 3, pp. 536-544.
[5]. Kalsi, S. S., Sidhu, T. S., and Singh, H., (2013A).
“Characterization of NiCrAlY Coatings on Ni- And Fe- based
Superalloys by the Cold Spray Process”. i-manager's
Journal on Material Science. Vol. 1(2), Jul-Sep 2013, Print
ISSN 2347–2235, E-ISSN 2347–615X, pp. 20-26.
[6]. Kalsi, S.S., Sidhu, T.S., and Singh, H., (2013B).
“Characterization of Cold-Sprayed NiCoCrAlY Coatings on
Fe-Based Superalloy and Hot Corrosion Behavior in Na SO - 2 4
NaCl Environment”. i-manager's Journal on Future
Engineering and Technology, Vol. 9(1), Aug-Oct 2013, Print
ISSN 0973-2632, E-ISSN 2230-7184, pp. 15-26.
[7]. Kalsi, S. S., Sidhu, T. S., and Singh, H., (2013C). “Hot
Corrosion in Bio Medical Waste Incinerator and Cold Spray
Coatings - A Review”. i-manager's Journal on Material
Science. Vol. 1(2), Jul-Sep 2013, Print ISSN 2347–2235, EISSN
2347–615X, pp. 1-12.
[8]. Kalsi, S. B. S., Sidhu T. S., and Singh H., (2013D).
“Chlorine Based Hot Corrosion Study of Cold Sprayed
NiCrAlY Coating”. Surf. Eng., Vol. 30(6), pp.422- 431.
[9]. Kalsi, S. B. S., Sidhu T. S., and Singh H., (2014A).
“Performance of Cold Spray Coating in Industrial Medical
Waste Incinerator”. Surf. Eng., Vol. 30(5), pp. 352-360.
[10]. Kalsi, S. S., Sidhu, T. S., Singh, H., and Karthikeyan, J.,
(2014B). “Behavior of Cold Spray Coating in Real
Incineration Environment”. Mater. Manufact. Process.,
DOI:10.1080/10426914.2014.912319.
[11]. Kalsi, S. S., Sidhu, T. S., Singh, H., and Karthikeyan, J.,
(2014C). “Analysis of material degradation for uncoated
and NiCoCrAlY cold spray coated Superfer 800H in the
secondary chamber of medical waste incinerator”.
Engineering Failure Analysis, Vol. 46, pp. 238-246.
[12]. Kalsi, S.S., Sidhu, T.S., and Singh, H., (2014D).
“Performance of Cold Spray Coatings On Fe-Based
o Superalloy in Na2SO4-NaCl Environment at 900 C”. Surf.
Coat. Technol., Vol. 240, pp. 456-463.
[13]. Kawahara, Y. and Kira, M., (1997). “Effect of Physical
Properties of Molten Deposits on High Temperature
Corrosion of Alloys in Waste Incineration Environment”.
Zairyo-to-Kankyo, Vol. 46(1), pp. 8-15.
[14]. Kawahara, Y., (2002A). “Recent Trends in
Development and Application of High-temperature
Corrosion-resistant Materials and Coatings in High Efficiency
Waste Incineration Boiler”. MTERE2, Vol. 41(3), pp. 190.
[15]. Kawahara Y., (2006). “Application of High
Temperature Corrosion-Resistant Materials and Coatings
Under Severe Corrosive Environment in Waste-to-Energy
Boilers”. Therm. Spray Technol., Vol. 16(2), pp. 202-213.
[16]. Kawahara, Y., Nakamura, M., Tsuboi, H. and K.
Yukawa, K., (1998). “Evaluation of New Corrosion Resistant
Super heater Tubings in High Efficiency Waste-to-Energy
Plants”. Corros., Vol. 54(7), pp. 576.
[17]. Lee, S. H., Themelis, N. J., and Castaldi, M. J., (2007).
“High-Temperature Corrosion in Waste-to-Energy Boilers”. J.
of Therm. Spray Technol., Vol. 16(1), pp.104-110.
[18]. Michelsen, H. P., Frandsen, F., Dam-Johansen, K., and
Larsen, O. H., (1998). “Deposition and High Temperature
Corrosion in a 10 MW Straw Fired Boiler”. Fuel Process.
Technol., Vol. 54, pp. 95-108.
[19]. Pedersen, J. I. A., Flemming, J. F., and Christian, R.,
(2009). “A Full-scale Study on the Partitioning of Trace Elements in Municipal Solid Waste Incinerations Effects of
Firing Different Waste Types”. Energy & Fuels, Vol. 23, pp. 3475-
3489.
[20]. Rademarkers, P., Hesseling, W., and Wetering, J.,
(2002). “Review on Corrosion in Waste Incinerators, and
Possible Effect of Bromine”. TNO Industrial Technology.
[21]. Rapp, R.A., (1986). “Chemistry and Electrochemistry
of the Hot Corrosion of Metals”. Corros., Vol. 42(10), pp. 568-577.
[22]. Ruth, L.A., (1998). “Energy From Municipal Solid Waste:
A Comparison With Coal Combustion Technology”. Prog.
Energy Combust. Sci., Vol. 24, pp. 545-564.
[23]. Shinata, Y., and Nishi, Y., (1986). “NaCl-Induced
Accelerated Oxidation of Chromium”. Oxidat. of Metals, Vol.
26, pp.201-212.
[24]. Singh, H., Sidhu, T.S., and Kalsi, S.S., (2014A).
“Development and Characterization of Cr C -NiCr Coated 3 2
Super alloy by Novel Cold Spray Process”. Surf. Eng. DOI: 1
0.1080/ 104269 14.2014 973599.
[25]. Singh, H., Sidhu, T.S., and Kalsi, S.S., (2014B). “Evolution
of Microstructure by High Velocity Impacts of Particles by
Cold Spray”. Mater. Manufact. Process. DOI:10.1080/ 10426914.2014.
994766.
[26]. Singh, H., Sidhu, T.S., and Kalsi, S.S., (2014C),
“Microstructure study of cold sprayed 50%Ni–50%Cr
coating on Inconel-601”. Surf. Eng., Vol. 31(11), pp. 825-831.
[27]. Singh, H., Sidhu, T.S., and Kalsi, S.S., (2014D). “Behavior
of Ni-based super alloys in actual waste incinerator plant
under cyclic conditions for 1000h at 900°C”. Corrosion, Vol.
70(12), pp. 1249-1263.
[28]. Singh, H., Sidhu, T.S., and Kalsi, S.S., (2015).
“Evaluation of characteristics and behavior of cold sprayed
Ni–20Cr coating at elevated temperature in waste
incinerator plant”. Surf. Coat. Technol., Vol. 261, pp. 375-384.
