i-manager Publications

Automation in Speed Control and Overcurrent Protection of Three Phase Induction Motor

M. M. Kharade*, N.R Kulkarni**

* PG Scholar, Department of Electrical Engineering, Modern College of Engineering, Pune, India.

** Professor and HOD, Department of Electrical Engineering, Modern College of Engineering, Pune, India.

Periodicity:February - April'2016
DOI : https://doi.org/10.26634/jic.4.2.4876

Abstract

The intent of the paper is to control the speed and give protection to Induction Motor (IM). Thereby it limits the starting current and protects the induction motor under load/ overload conditions. The control panel is designed to control the speed and protection of 3 phase IM and required control is done by PLC (Programmable Logic Controller). The motor is run at no load condition and load condition, for manual mode and PLC mode. At manual mode, if frequency is changed, the motor speed changes by keeping v/f ratio constant but, regulation in speed is high. At PLC mode, if frequency is changed, the motor speed remains constant, by keeping v/f ratio constant and speed regulation zero. The speed control of the induction motor in manual and PLC mode is accessed by using the selector switch [1]. SCADA (Supervisory Control and Data Aquisition) is used for monitoring and controlling of induction motor performance and it also collects performance data of the induction motor. This is how the starting, control the speed and protection of IM is achieved by using PLC and SCADA, and the operation is sufficiently high efficient and reliable [1], [2].

Keywords

PLC, SCADA, Induction Motor, V/F Drive, Fault Diagnosis.

How to Cite this Article?

Kharade, M.M., and Kulkarni, N.R. (2016). Automation in Speed Control and Overcurrent Protection of Three Phase Induction Motor. i-manager’s Journal on Instrumentation and Control Engineering, 4(2), 1-6. https://doi.org/10.26634/jic.4.2.4876

References

[1]. K. Sandeep Kumar, and K. Pritam Satsangi, (2007). “Micro –Controller Based Closed Loop Control of Induction Motor Using V/F Method”. IET International Conference on Information and Communication Technology in Electrical Science, pp.340-342 .

[2]. Mineo Tsuji, Shuo Chen, and Shin-ichi Hamasaki, (2008). “A Noval V/F Control of Induction Motors for Wide and Precise Speed Operation”. IEEE International Symposium Power Electronics, Electrical Drives, Automation and Motion, pp.1130-1135.

[3]. Maria G. Ioannides, (2004). “Design and Implementation of PLC-Based Monitoring Control System for Induction Motor”. IEEE Transactions on Energy Conservation, Vol. 19, No. 3.

[4]. N. D. Ramesh, (2011). “Programmable Logic Controllers and SCADA. Seminar Projects.

[5]. S. Da'na, (2008). “Development of a Monitoring and Control Platform for PLC based Applications”. Journal Computer Standards & Interfaces, Vol. 30, No. 3, pp. 157- 166.

[6]. Jignesha Ahir, (2011). “Design and Development of PLC and SCADA Based Control Panel for Continuous Monitoring of 3 Phase Induction Motor”. National Conference on Recent Trends in Engineering & Technology..

[7]. Mahir Zajmovic, Hadzib Salkic, and Sasa Stanic, (2012). “Management of Induction (asynchronous) Motor using PLC”. Journal of Information Technology and Applications, Vol.2, pp. 95-102.

[8]. Ravi Masand, Deepika Jadwani, and S.P. Shukla, (2013). “Fault Diagnosis of Induction Motor using PLC & SCADA”. International Journal of Advanced Research in Electrical, Electronics and Instrumentation Engineering, Vol.2, No.12.

[9]. Rinchen Geongmit Dorjee, (2014). “Monitoring and Control of a Variable Frequency Drives using PLC and SCADA”. International Journal on Recent and Innovation Trends in Computing and Communication, Vol. 2, No.10.

[10]. D. Amudhavalli, and L. Narendra, (2012). “Speed control of an Induction Motor by V/F Method using an Improved Z Source Inverter”. IEEE International Conference on Emerging Trends in Electrical Engineering and Energy Management, pp.436-440.

[11]. Cristina Anita Bejan, Mihai Iacob and Gheorghe- Daniel Andreescu, (2009). "SCADA Automation System th Laborator y, Elements and Applications". IEEE 7 International Symposium on Intelligent Systems and Informatics, pp.181-186.

[12]. Mini S. Thomas, Pramod Kumar, and V.K. Chandna, (2004). "design, Development, and Commissioning of a Supervisory Control and Data Acquisition (SCADA) Laboratory for Research and Training". IEEE Transactions on Power System, Vol.19, No. 3, pp.1582-1588.

[13]. Al-Ali, A.R., (2000). “A PLC Based Power Factor Controller for a 3-phase Induction Motor”. IEEE International conference on Industry Applications, Vol.2, pp.1065-1072.

If you have access to this article please login to view the article or kindly login to purchase the article

Single Article

	North Americas,UK, Middle East,Europe		India	Rest of world
	USD	EUR	INR	USD-ROW
Online	15	15

ADD TO CART

Options for accessing this content:

If you would like institutional access to this content, please recommend the title to your librarian.
If you already have i-manager's user account: Login above and proceed to purchase the article.
New Users: Please register, then proceed to purchase the article.