References
[1]. Singh J. (2008). “Experimental investigation for tool life
enhancement of single point cutting tool with cryogenic
treatment”. M.Tech. Thesis, P.T.U. Jalandhar, pp.12-47.
[2]. Aujla H.S., Singh R. (2008). “Applications of cryogenic
treatment for enhancing the machining properties of
titanium alloy (Ti-6Al-4V)”, Manufacturing Technology
Today, Vol. 7, pp.22-26.
[3]. Singh K. (2009). “Study of the effect of cryogenic
treatment on various tools for machining cost reduction: A
case study” M.Tech. Thesis, P.T.U. Jalandhar, pp. 10-32.
[4]. Armarego EJA, Brown RH. (1969). “ The machining of metals”, New Jersey: Prentice-Hall.
[5]. Boothroyd G. (1965). “Fundamentals of metal
machining”, Washington: Edward Arnold.
[6]. Baradie MA EI. (1996). “Cutting Fluids: Part I.
Characterisation”. J. Mater. Process. Technol. Vol.56, pp.
789-797
[7]. Gaitondea V.N., Karnik S.R., Davim Paulo J. (2008).
“Selection of optimal MQL and cutting conditions for
enhancing machinability in turning of brass”. Journal of
materials processing technology, Vol.204, pp.459–464
[8]. Hong S. Y. and Ding Y. (2001). “Cooling approaches
and cutting temperatures in cryogenic machining of Ti-6Al-
4V”. International Journal of Machine Tools and
Manufacture, Vol.41 (10), pp.1417-1437
[9]. Werthem, R. and Rotberg, J. “Influence of high pressure
flushing through the rake face of the tool”. Annals CIRP, Vol.
41 (1), 101-106.
[10]. Bartley EW. Machinery (E) 1953:83.
[11]. Hollis WS. “The application of controlled atmosphere
in machining of metals”. Int J Mach Tool Des, Vol.1,
pp.59–78.
[12]. Uhera K, Kumagai S. (1968). “Chip formation, surface
roughness, cutting forces and tool wear in cryogenic
machining”. Annals CIRP, Vol.17, No.1, pp.93-98.
[13]. Chattopadhyay AB, Roy TK, Bhattacharyya A. (1972).
“Application of cryogenics in metal cutting”. J Inst Eng
(India).
[14]. Paul S, Dhar NR, Chattopadhyay AB. “Beneficial effects
of cryogenic cooling over dry and wet machining on tool
wear and surface finish in turning AISI 1060 steel”. J Mater
Process Technol , Vol. 116, pp.44–8.
[15]. Hong SY, Markus I, Jeong W. (2001). “New cooling
approach and tool life improvement in cryogenic
machining of titanium alloy Ti–6Al–4V”. Int J Mach Tools
Manuf , Vol. 41, pp.2245–60.
[16]. Çakir O, Kiyak M, Altan E. (2004). “Comparison of
gases applications to wet and dry cuttings in turning”. J
Mater Process Technol, Vol.153–154, pp.35–41.
[17]. Liu J, Han R, Sun Y. (2005). “Research on experiments
and action mechanism with water vapor as coolant and
lubricant in Green cutting”. Int J Mach Tools Manuf, Vol. 45,
pp.687–94.
[18]. Dhar N.R., Kamruzzaman, M. (2007). “Cutting
temperature, tool wear, surface roughness and dimensional
deviation in turning of AISI 4037 steel under cryogenic
condition”. International Journal of machine tools and
manufacture, Vol. 47, pp.754-759.
[19]. Kumar, P., Barua, P.B., Gaindhar, J.L. (2000). “Quality
optimization (multi-characteristic) through Taguchi's
technique and utility concept”. Qual. Reliab. Eng. Int. Vol.
16, pp.475–485.
[20]. Phadke, M.S. (1989). “Quality Engineering Using
Robust Design”. Prentice Hall, Englewood Cliffs, NJ.
[21]. Ross, P.J. Taguchi, (1996). “Techniques for Quality
Engineering”. McGraw-Hill, New York .
