i-manager Publications

Enhancing Efficiency of PVT Systems with Finned PCM Technology

D. Kameswara Rao*, K. Sudhakar Reddy**, V. V. Subba Rao***

*-** Department of Mechanical Engineering, Mahatma Gandhi Institute of Technology, Hyderabad, India.

*** Department of Mechanical Engineering, Jawaharlal Nehru Technological University, Andhra Pradesh, India.

Periodicity:July - September'2023
DOI : https://doi.org/10.26634/jme.13.3.19510

Abstract

An increase in solar panel temperature reduces panel electrical efficiency, necessitating efficient active and passive cooling methods. This study proposes the introduction of Phase Change Material (PCM) on the backside of the solar panel, along with extended fins. The experimental investigation focuses on utilizing extended surfaces known as Thermal Conductivity Enhancers (TCE) in the PV-PCM (Photo Voltaic - Phase Change Material) module. Two independent aluminum fin designs are considered to enhance the thermal conductivity (k) of the PCM, analyzing the influence of the surface contact area and material volume fraction on the PV surface temperature during the charging period of the Production Validation Test-Pulse Code Modulation (PVT-PCM) panel. The experimental results demonstrate that an array of longitudinal and lateral fins with an optimal thickness of 3 mm maintains a lower temperature gradient throughout the process, significantly reducing the surface temperature of the PV panel. Numerical simulations using ANSYS Fluent were conducted for both the lateral- and cross-fin configurations, showing good agreement with the observed experimental data. This study aims tofill this research gap by optimizing PV panel cooling through the selection ofthe fin geometry, size, shape, and PCM.

Keywords

PVT-PCM, Conductivity, Thermal Storage, Nucleation Rate, Numerical Simulations.

How to Cite this Article?

Rao, D. K., Reddy, K. S., and Rao, V. V. S. (2023). Enhancing Efficiency of PVT Systems with Finned PCM Technology. i-manager’s Journal on Mechanical Engineering, 13(3), 21-35. https://doi.org/10.26634/jme.13.3.19510

References

[1]. Atkin, P., & Farid, M. M. (2015). Improving the efficiency of photovoltaic cells using PCM infused graphite and aluminium fins. Solar Energy, 114, 217-228.

[2]. Baby, R., & Balaji, C. (2013a). Experimental investigations on thermal performance enhancement and effect of orientation on porous matrix filled PCM based heat sink. International Communications in Heat and Mass Transfer, 46, 27-30.

[3]. Baby, R., & Balaji, C. (2013b). Thermal optimization of PCM based pin fin heat sinks: an experimental study. Applied Thermal Engineering, 54(1), 65-77.

[4]. Biwole, P. H., Eclache, P., & Kuznik, F. (2013). Phasechange materials to improve solar panel's performance. Energy and Buildings, 62, 59-67.

[5]. Biwole, P. H., Groulx, D., Souayfane, F., & Chiu, T. (2018). Influence of fin size and distribution on solid-liquid phase change in a rectangular enclosure. International Journal of Thermal Sciences, 124, 433-446.

[6]. Brano, V. L., Ciulla, G., Piacentino, A., & Cardona, F. (2014). Finite difference thermal model of a latent heat storage system coupled with a photovoltaic device: Description and experimental validation. Renewable Energy, 68, 181-193.

[7]. Browne, M. C., Lawlor, K., Kelly, A., Norton, B., & Mc Cormack, S. J. (2015a). Indoor characterisation of a photovoltaic/thermal phase change material system. Energy Procedia, 70, 163-171.

[8]. Browne, M. C., Norton, B., & McCormack, S. J. (2015b). Phase change materials for photovoltaic thermal management. Renewable and Sustainable Energy Reviews, 47, 762-782.

[9]. Chandel, S. S., & Agarwal, T. (2017). Review of cooling techniques using phase change materials for enhancing efficiency of photovoltaic power systems. Renewable and Sustainable Energy Reviews, 73, 1342-1351.

[10]. Chen, Z., Gao, D., & Shi, J. (2014). Experimental and numerical study on melting of phase change materials in metal foams at pore scale. International Journal of Heat and Mass Transfer, 72, 646-655.

[11]. Du, D., Darkwa, J., & Kokogiannakis, G. (2013). Thermal management systems for photovoltaics (PV) installations: A critical review. Solar Energy, 97, 238-254.

[12]. Fan, L. W., Xiao, Y. Q., Zeng, Y., Fang, X., Wang, X., Xu, X., ... & Cen, K. F. (2013). Effects of melting temperature and the presence of internal fins on the performance of a phase change material (PCM)-based heat sink. International Journal of Thermal Sciences, 70, 114-126.

[13]. Fan, L. W., Zhu, Z. Q., Zeng, Y., Xiao, Y. Q., Liu, X. L., Wu, Y. Y., ... & Cen, K. F. (2015). Transient performance of a PCM-based heat sink with high aspect-ratio carbon nanofillers. Applied Thermal Engineering, 75, 532-540.

[14]. Hachem, F., Abdulhay, B., Ramadan, M., El Hage, H., El Rab, M. G., & Khaled, M. (2017). Improving the performance of photovoltaic cells using pure and combined phase change materials-Experiments and transient energy balance. Renewable Energy, 107, 567-575.

[15]. Hasan, A., McCormack, S. J., Huang, M. J., & Norton, B. (2010). Evaluation of phase change materials for thermal regulation enhancement of building integrated photovoltaics. Solar Energy, 84(9), 1601-1612.

[16]. Hasan, A., McCormack, S. J., Huang, M. J., Sarwar, J., & Norton, B. (2015). Increased photovoltaic performance through temperature regulation by phase change materials: Materials comparison in different climates. Solar Energy, 115, 264-276.

[17]. Hasan, A., Sarwar, J., Alnoman, H., & Abdelbaqi, E. S. (2017). Yearly energy performance of a photovoltaicphase change material (PV-PCM) system in hot climate. Solar Energy, 146, 417-429.

[18]. Ho, C. J., Tanuwijava, A. O., & Lai, C. M. (2012). Thermal and electrical performance of a BIPV integrated with a microencapsulated phase change material layer. Energy and Buildings, 50, 331-338.

[19]. Huang, M. J. (2011). The effect of using two PCMs on the thermal regulation performance of BIPV systems. Solar Energy Materials and Solar Cells, 95(3), 957-963.

[20]. Huang, M. J., Eames, P. C., & Norton, B. (2004). Thermal regulation of building-integrated photovoltaics using phase change materials. International Journal of Heat and Mass Transfer, 47(12-13), 2715-2733.

[21]. Huang, M. J., Eames, P. C., & Norton, B. (2006). Phase change materials for limiting temperature rise in building integrated photovoltaics. Solar Energy, 80(9), 1121-1130.

[22]. Huang, M. J., Eames, P. C., Norton, B., & Hewitt, N. J. (2011). Natural convection in an internally finned phase change material heat sink for the thermal management of photovoltaics. Solar Energy Materials and Solar Cells, 95(7), 1598-1603.

[23]. Indartono, Y. S., Suwono, A., & Pratama, F. Y. (2016). Improving photovoltaics performance by using yellow petroleum jelly as phase change material. International Journal of Low-Carbon Technologies, 11(3), 333-337.

[24]. Khanna, S., Reddy, K. S., & Mallick, T. K. (2017). Performance analysis of tilted photovoltaic system integrated with phase change material under varying operating conditions. Energy, 133, 887-899.

[25]. Khanna, S., Reddy, K. S., & Mallick, T. K. (2018c). Optimization of finned solar photovoltaic phase change material (finned pv pcm) system. International Journal of Thermal Sciences, 130, 313-322.

[26]. Khanna, S., Reddy, K. S., & Mallick, T. K. (2018a). Climatic behaviour of solar photovoltaic integrated with phase change material. Energy Conversion and Management, 166, 590-601.

[27]. Khanna, S., Reddy, K. S., & Mallick, T. K. (2018b). Optimization of solar photovoltaic system integrated with phase change material. Solar Energy, 163, 591-599.

[28]. Kibria, M. A., Saidur, R., Al-Sulaiman, F. A., & Aziz, M. M. A. (2016). Development of a thermal model for a hybrid photovoltaic module and phase change materials storage integrated in buildings. Solar Energy, 124, 114-123.

[29]. Ma, T., Yang, H., Zhang, Y., Lu, L., & Wang, X. (2015). Using phase change materials in photovoltaic systems for thermal regulation and electrical efficiency improvement: A review and outlook. Renewable and Sustainable Energy Reviews, 43, 1273-1284.

[30]. Mahamudul, H., Rahman, M. M., Metselaar, H. S. C., Mekhilef, S., Shezan, S. A., Sohel, R., ... & Badiuzaman, W. N. I. (2016). Temperature regulation of photovoltaic module using phase change material: A numerical analysis and experimental investigation. International Journal of Photoenergy, 2016, 1-8.

[31]. Park, J., Kim, T., & Leigh, S. B. (2014). Application of a phase-change material to improve the electrical performance of vertical-building-added photovoltaics considering the annual weather conditions. Solar Energy, 105, 561-574.

[32]. Rao, D. K., Reddy, K. S., & Subba Rao, V. V. (2022). Experimental and Numerical study of Photo voltaic Thermal Phase change Material Heat transfer augmentation with encapsulation of embedded material/fins. Ecological Engineering & Environmental Technology, 23(4), 149-161.

[33]. Sharma, S., Tahir, A., Reddy, K. S., & Mallick, T. K. (2016). Performance enhancement of a BuildingIntegrated Concentrating Photovoltaic system using phase change material. Solar Energy Materials and Solar Cells, 149, 29-39.

[34]. Shukla, A., Kant, K., Sharma, A., & Biwole, P. H. (2017). Cooling methodologies of photovoltaic module for enhancing electrical efficiency: A review. Solar Energy Materials and Solar Cells, 160, 275-286.

[35]. Singh, D., Bharadwaj, S. S., & Bansal, N. K. (1982). Thermal performance of a matrix air heater. International Journal of Energy Research, 6(2), 103-110.

[36]. Skoplaki, E., & Palyvos, J. A. (2009). On the temperature dependence of photovoltaic module electrical performance: A review of efficiency/power correlations. Solar Energy, 83(5), 614-624.

[37]. Smith, C. J., Forster, P. M., & Crook, R. (2014). Global analysis of photovoltaic energy output enhanced by phase change material cooling. Applied Energy, 126, 21-28.

[38]. Sundarram, S. S., & Li, W. (2014). The effect of pore size and porosity on thermal management performance of phase change material infiltrated microcellular metal foams. Applied Thermal Engineering, 64(1-2), 147-154.

[39]. Xiao, X., Zhang, P., & Li, M. (2013). Preparation and thermal characterization of paraffin/metal foam composite phase change material. Applied Energy, 112, 1357-1366.

If you have access to this article please login to view the article or kindly login to purchase the article

Single Article

	North Americas,UK, Middle East,Europe		India	Rest of world
	USD	EUR	INR	USD-ROW
Online	15	15

ADD TO CART

Options for accessing this content:

If you would like institutional access to this content, please recommend the title to your librarian.
If you already have i-manager's user account: Login above and proceed to purchase the article.
New Users: Please register, then proceed to purchase the article.