i-manager Publications

Performance Validation of Brushless Resolver and Implementation with Ad2s1210a RDC Converter

Dommeti Rajesh*, Gautam Moni Patro**, P. Mallikarjuna Rao***

*-** Scholar, Department of Electrical Engineering, AUCE(A), Andhra University, Visakhapatnam, India.

*** Professor, Department of Electrical Engineering, AUCE(A), Andhra University, Visakhapatnam, India.

Periodicity:October - December'2017
DOI : https://doi.org/10.26634/jee.11.2.13852

Abstract

Position feedback requires precise and repeatable indication of rotor position for any closed loop control system. In case of Robotics, motion control devices and multiple pole motors require high sensitivity of the rotator position without any time lapse. Modern motion control methods provide an accurate, fast rate, and low costposition feedback with greater flexibility than older sensing methods. The Resolver technology has been used in an industrial environment for many years in angular position transducers applications. Resolvers are highly robust in nature of operation, and can work even in places, where other electronics based encoders, potentiometers fail. A Brushless resolver is basically rotating transformers integrated with built in two phase machine as rugged as the motor and withstands for High speeds with optimum resolutions. Recent progression in the high resolution R/D converter (RDC) chip technology provides an accurate feedback with reliability and Higher resolution. In this paper, a brushless resolver performance was presented with latest AD2S1210 RDC and 16 bit output interface to dSPIC30F Microcontroller. Also a mathematical model for Resolver and RDC are developed to establish the theoretical performance of the setup.

Keywords

How to Cite this Article?

Rajesh, D., Patro, G. M., and Pasumarthi, M. R. (2017). Performance Validation of Brushless Resolver and Implementation with Ad2s1210a RDC Converter. i-manager’s Journal on Electrical Engineering, 11(2), 7-15. https://doi.org/10.26634/jee.11.2.13852

References

[1]. Aksenenko, V. D., Aksenenko, D. V., & Matveev, S. I. (2003, April). Digital signal processing in angle-to-digital conversion. In Conference Proceedings of Int. Signal Processing Conference.

[2]. Analog Devices (2008). Variable resolution 10-bit to 16-bit r/d converter with reference oscillator. Catalogue of AD2S1210, 1-19.

[3]. Arab-Khaburi, D., Tootoonchian, F., & Nasiri-Gheidari, Z. (2007). Parameter identification of a brushless resolver using charge response of stator current. Iranian Journal of Electrical and Electronic Engineering, 3(1), 42-52.

[4]. Arab-Khaburi, D., Tootoonchian, F., & Nasiri-Gheidari, Z. (2008). Dynamic performance prediction of brushless resolver. Iranian Journal of Electrical & Electronic Engineering, 4(3), 94-103.

[5]. Axsys Company R&D Group, Pancake Resolvers Handbook, http://www.Axsys.com, revised at 15 December 2006.

[6]. Bunte, A., & Beineke, S. (2004). High-performance speed measurement by suppression of systematic resolver and encoder errors. IEEE transactions on industrial electronics, 51(1), 49-53.

[7]. Caricchi, F., Capponi, F. G., Crescimbini, F., & Solero, L. (2001). Sinusoidal brushless drive with low-cost linear Hall effect position sensors. In Power Electronics Specialists nd Conference, 2001. PESC. 2001 IEEE 32 Annual (Vol. 2, pp. 799-804). IEEE.

[8]. Harnefors, L., & Nee, H. P. (2000). A general algorithm for speed and position estimation of AC motors. IEEE Transactions on Industrial Electronics, 47(1), 77-83.

[9]. Hoseinnezhad, R., & Harding, P. (2005, December). A novel hybrid angle tracking observer for resolver to digital conversion. In Decision and Control, 2005 and 2005 th European Control Conference. CDC-ECC'05. 44 IEEE Conference on (pp. 7020-7025). IEEE.

[10]. Kitazawa, K. (2009). Principle and application of resolvers for hybrid electric vehicles. In Proc. of Innovative Automotive Transmissions Conference.

[11]. Li, S. J., Zhou, Q. X., & Lu, G. (2007). Digital Calibration and Compensation Method for Angle Measure System Based on Resolver-RDC [J]. Small & Special Electrical Machines, 6, 010.

[12]. Qixun, Z., Shengjin, L., Gang, L., & Yong, Z. (2008, October). Crossed-feedback control of dualredundancy permanent magnetic brushless dc servo system used in electro-hydrostatic actuator. In Electrical Machines and Systems, 2008. ICEMS 2008. International Conference on (pp. 1237-1241). IEEE.

	North Americas,UK, Middle East,Europe		India	Rest of world
	USD	EUR	INR	USD-ROW
Pdf	35	35	200	20
Online	35	35	200	15
Pdf & Online	35	35	400	25

Performance Validation of Brushless Resolver and Implementation with Ad2s1210a RDC Converter

Abstract

Keywords

How to Cite this Article?

References

If you have access to this article please login to view the article or kindly login to purchase the article

Purchase Instant Access

Options for accessing this content: