References
[1]. Dalle Donne, M., and Meyer, L. (1977). Turbulent convective heat transfer from rough surfaces with two-dimensional rectangular ribs, Int. J. Heat Mass Transfer, Vol. 20, pp. 583-620.
[2]. Zhu, Z., Yang, H., and Chen, T. (2010). Numerical study of turbulent heat and fluid flow in a straight square duct at higher Reynolds numbers, Int. J. Heat Mass Transfer, Vol. 53, pp. 356-364.
[3]. Meyer, J.P., and Olivier, J.A. (2011). Transitional flow inside enhanced tubes for fully developed and developing flow with different types of inlet disturbances: Part II–heat transfer, Int. J. Heat Mass Transfer, Vol. 54, pp. 1598-1607.
[4]. Dalle Donne, M. (1975). The development of the gas cooled fast breeder reactor, karl wirtz, gewidmet zum 65. Geburtstag, KFK 2200, In beitrage zur kerntechnik.
[5]. Melese D'Hospital, G. (1973). Merit index for gas cooled reactor heat transfer, Nucl. Sci. Engng., Vol. 50, pp. 83-85.
[6]. Lee, S.H. (2010). Numerical study of convective heat transfer to supercritical water in rectangular ducts, Int. Communications in Heat and Mass Transfer, Vol. 37, pp. 1465-1470.
[7]. Barbosa Saldana, J.G., Anand, N.K., and Sarin, V. (2005). Numerical simulation of mixed convection flow over a horizontal backward facing step, J. of Heat Transfer, Vol. 127, pp. 1027-1036.
[8]. Eaton, J.K. and Johnston, J.P. Sep. (1981). A review of research on subsonic turbulent flow reattachment, AIAA Journal, Vol. 19, No. 9.
[9]. Kim, B.N. and Chung, M.K. Oct. (1994). Experimental study of roughness effect on the separated flow over a backward-facing step, AIAA Journal, Vol. 33, No. 1.
[10]. Acharya, S., Dutta, S. and Myrum, T.A. (1998). Heat transfer in turbulent flow past a surface-mounted two-dimensional rib, J. of Heat Transfer, Vol. 120, pp. 724-734.
[11]. Chandra, P.R., Alexander, C.R. and Han, J.C. (2003). Heat transfer and friction behaviors in rectangular channels with varying number of ribbed walls, Int. J. Heat Mass Transfer, Vol. 46, pp. 481-495.
[12]. Jenn-Jiang Hwang (1998). Heat transfer-friction characteristic comparison in rectangular ducts with slit and solid ribs mounted on one wall, J. of Heat Transfer, Vol. 120, pp. 709-716.
[13]. Karwa, R., Solanki, S.C. and Saini, J.S. (1999). Heat transfer coefficient and friction factor correlations for the transitional flow regime in rib-roughened rectangular ducts, Int. J. Heat Mass Transfer, Vol. 42, pp. 1597-1615.
[14]. Michael, K., Jensen, and Alex Vlakancic (1999). Experimental investigation of turbulent heat transfer and fluid flow in internally finned tubes, Int. J. Heat Mass Transfer, Vol. 42, pp. 1343-1351.
[15]. Tsia, J.P., and Hwang, J.J. (1999). Measurements of heat transfer and fluid flow in rectangular duct with alternate attached-detached rib-arrays, Int. J. Heat Mass Transfer, Vol. 42, pp. 2071-2083.
[16]. Wu, S., Li, Y., Chen, Y., and Xiao, L. (2007). Exergy transfer characteristics of forced convective heat transfer through a duct with constant wall temperature, Energy, Vol. 32, pp. 2385-2395.
[17]. Mousa, M.G. (2013). Thermal performance of pin–fin heat sink subject in magnetic field inside rectangular channels, Experimental Thermal and Fluid Science, Vol. 44, pp. 138-146.
[18]. Promvonge, P., Skullong, S., Kwankaomeng, S., and Thiangpong, C. (2012). Heat transfer in square duct fitted diagonally with angle-finned tape, Int. Communications in Heat and Mass Transfer, Vol. 39, pp. 617-624.
[19]. Hwang, S.D., Jang, I.H., and Cho, H. (2006). Experimental study on flow and local heat/mass transfer characteristics inside corrugated duct, Int. J. of Heat and Fluid Flow, Vol. 27, pp. 21-32.
[20]. Wu, S., Xiao, L., Chen, S., Li, Y., Xu, J., and Liu, C. (2012). Exergo-economic criteria for performance evaluation of enhanced heat transfer duct with constant wall temperature, Applied Thermal Engineering, Vol. 36, pp. 393-402.
[21]. Lee, S. (2008). Convective heat transfer to water near the critical region in a horizontal square duct, Int. J. Heat Mass Transfer, Vol. 51, pp. 2930-2939.
[22]. Zhang, L., and Chen, Z. (2011). Convective heat transfer in cross-corrugated triangular ducts under uniform heat flux boundary conditions, Int. J. Heat Mass Transfer, Vol. 54, pp. 597-605.
[23]. Launder, B. E. and Spalding, D.B. (1972). Mathematical models of turbulence, Academic Press, London & NY.
[24]. Schlichting, H. (1968). Boundary layer theory, McGraw Hill, N.Y, pp. 553-586.
[25]. Hinze, J.O. (1959). Turbulence, McGraw Hill, N.Y.
[26]. Mc Guirk, J. J., May (1975). Prediction of turbulent buoyant jets in co-flowing streams, Ph.D. Thesis, Imperial College.
[27]. Bird, R.B., Stewart, W.E., and Lightfoot, E.N. (1960). Transport phenomena, Wiley International Edition, N.Y.
[28]. Jayatillaka, C.L.V. (1966). The influence of Prandtl number and surface roughness on the resistance of the laminar sub-layer to momentum and heat transfer, Imperial College, Mech. Eng. Dep., Report TWF/R/2.
[29]. Launder, B.E., and Spalding, D.B. (1973). The numerical computation of turbulent flows, Imperial College, M.E.D., Report HTS/73/2.
[30]. Spalding, D.B., and Jayatillaka, C.L.V. (1964). A survey of the theoretical and experimental information on the resistance of the laminar sub-layer to heat and mass transfer, Proceedings 2nd All Soviet Union Conference on HMT Minsk, USSR.
[31]. Kays, W.M., and Muffat, R.J. (1975). The behavior of transpired turbulent boundary layers, Academic Press, Edition by Launder, B.E.
[32]. Patankar, S.V. (1980). Numerical heat transfer and fluid flow, Hemisphere Publishing Corporation.
[33]. Tong-Miin Liou, J., Hwang and Chen, S. (1993). Simulation and measurement of enhanced turbulent heat transfer in a channel with periodic ribs on one principal wall, Int. J. Heat Mass Transfer, Vol. 36, pp. 507-517.
[34]. Nie, J.H., and Armaly, B.F. (2003). Reattachment of three-dimensional flow adjacent to backward-facing step, ASME J. Heat Transfer, Vol. 125, pp. 422-428.
