i-manager Publications

Experimental and Numerical Research on the Effect of Winding Angles on the Torsional Strength of Glass Fiber Winding Hybrid Aluminium Shaft

Bhupendra Pardhi*, Murlidhar Patel**

* Department of Mechanical Engineering, Institute of Technology, Guru Ghasidas Vishwavidyalaya, Bilaspur, Chhattisgarh, India.

** Department of Mechanical Engineering, PDPM Indian Institute of Information Technology, Design and Manufacturing (IIITDM), Jabalpur, Madhya Pradesh, India.

Periodicity:April - June'2021
DOI : https://doi.org/10.26634/jms.9.1.18268

Abstract

The present work deals with the torsional behaviour of the glass fiber wounded aluminium shaft. This hybrid composite shaft consists of an aluminium tube wounded with three layers of glass/epoxy. In this paper, experimental as well as numerical evaluation of the maximum torsion strength capacity of the hybrid composite shafts at the different winding angles (30⁰, 45⁰ and 60⁰) are presented. The torsion behaviour has been experimentally analysed for the hybrid composite shafts using an axial torsion machine at room temperature. For finite element analysis (FEA) of the hybrid composite shaft, the CATIA modelling software has been used for designing, and ANSYS software has been used to analyse the torsional behaviour of the designed hybrid composite under static torsion. Good agreements were predicted between the numerical and experimental results. Both numerical and experimental results show that the static torque capacity of the hybrid composite shaft is significantly affected by the winding angle, and the maximum static torsional capacity of the hybrid composite aluminium shaft has been found at a winding angle of 45⁰.

Keywords

Aluminium Tube, Glass/Epoxy, Hybrid Composite Shaft, Winding Angle, Torsion.

How to Cite this Article?

Pardhi, B., and Patel , M. (2021). Experimental and Numerical Research on the Effect of Winding Angles on the Torsional Strength of Glass Fiber Winding Hybrid Aluminium Shaft. i-manager's Journal on Material Science, 9(1), 1-12. https://doi.org/10.26634/jms.9.1.18268

References

[1]. Badie, M. A., Mahdi, A., Abutalib, A. R., Abdullah, E. J., & Yonus, R. (2006). Automotive composite driveshafts: Investigation of the design. International Journal of Engineering and Technology, 3(2), 227-237.

[2]. Bert, C. W., & Kim, C. D. (1995). Analysis of buckling of hollow laminated composite drive shafts. Composites Science and Technology, 53(3), 343–351. https://doi.org/ 10.1016/0266-3538(95)00006-2

[3]. Lee, D. G., Kim, H. S., Kim, J. W., & Kim, J. K. (2004). Design and manufacture of an automotive hybrid aluminum/composite drive shaft. Composite Structures, 63(1), 87-99. https://doi.org/10.1016/S0263-8223(03) 00136-3

[4]. Mathis, R. S., & Ferracane, J. L. (1989). Properties of a glass-ionomer/resin-composite hybrid material. Dental Materials, 5(5), 355–358. https://doi.org/10.1016/0109- 5641(89)90130-9

[5]. Mutasher, S. A. (2009). Prediction of the torsional strength of the hybrid aluminum/composite drive shaft. Materials and Design, 30(2), 215–220. https://doi.org/10. 1016/j.matdes.2008.05.024

[6]. Patel, M., Kumar, A., Pardhi, B., & Pal, M. (2020a). Abrasive, erosive and corrosive wear in slurry pumps – A review. International Research Journal of Engineering and Technology, 7(3), 2188–2195. https://doi.org/10.1016/j. future.2018.04.097

[7]. Patel, M., Kumar, A., Sahu, S. K., & Singh, M. K. (2020b). Mechanical behaviors of ceramic particulate reinforced aluminium metal matrix composites–A review. International Research Journal of Engineering and Technology (IRJET), 7(1), 201-204.

[8]. Patel, M., Pardhi, B., Chopara, S., & Pal, M. (2018). Lightweight composite materials for automotive - A review. International Research Journal of Engineering and Technology, 5(11), 41–47.

[9]. Patel, M., Pardhi, B., Pal, M., & Singh, M. K. (2019a). SiC particulate reinforced aluminium metal matrix composite. Advanced Journal of Graduate Research, 5(1), 8–15. https://doi.org/10.21467/ajgr.5.1.8-15

[10]. Patel, M., Pardhi, B., Sahu, D. P., & Sahu, S. K. (2021). Different techniques used for fabrication of aluminium metal matrix composites. International Journal of Engineering and Techniques, 7(1), 1–8. https://doi.org/10. 29126/23951303/IJET-V7I1P1

[11]. Patel, M., Pardhi, B., Sahu, S. K., & Singh, M. K. (2020c). Characterization of brinell hardness, impact toughness and sliding wear resistance properties of Al₅Mg₅Zn/WO₃ -p metal matrix composite. i-manager's Journal on Material Science, 7(4), 23-29. https://doi.org/ 10.26634/jms.7.4.16125

[12]. Patel, M., Pardhi, B., Sahu, S. K., Kumar, A., & Singh, M. K. (2019b). Evaluation of hardness, toughness and sliding wear resistance after replacing Zn into SiC in Al₅Mg₅Zn/3 WO₃-p metal matrix composite. International Journal for Research in Engineering Application & Management, 5(03), 106-110.

[13]. Patel, M., Sahu, S. K., & Singh, M. K. (2020d). Abrasive wear behavior of SiC particulate reinforced AA5052 metal matrix composite. Materials Today: Proceedings, 33, 5586–5591. https://doi.org/10.1016/j.matpr.2020.03.572

[14]. Patel, M., Sahu, S. K., & Singh, M. K. (2020e). Fabrication and investigation of mechanical properties of SiC particulate reinforced AA5052 metal matrix composite. Journal of Modern Materials, 7(1), 26–36. https://doi.org/ 10.21467/jmm.7.1.26-36

[15]. Patel, M., Sahu, S. K., & Singh, M. K. (2020f). Mechanical, tribological and corrosion behaviour of aluminium alloys and particulate reinforced aluminium or aluminium alloy metal matrix composites - A review. i-manager's Journal on Material Science, 8(2), 40–55. https://doi.org/10.26634/ jms.8.2.16759

[16]. Patel, M., Sahu, S. K., Singh, M. K., & Kumar, A. (2020g). Sliding wear behavior of particulate reinforced aluminium metal matrix composites. International Journal of Engineering Research in Current Trends, 2(3), 8–13.

[17]. Patel, M., Singh, M. K., & Sahu, S. K. (2020h). Abrasive wear behaviour of sand cast B C particulate reinforced 4 AA5052 metal matrix composite. In B. Deepak, D. Parhi, & P. C. Jena (Eds.), Innovative Product Design and Intelligent Manufacturing Systems, (pp. 359–369). Singapore: Springer. https://doi.org/10.1007/978-981-15-2696-1_35

[18]. Shokrieh, M. M., Hasani, A., & Lessard, L. B. (2004). Shear buckling of a composite drive shaft under torsion. Composite Structures, 64(1), 63–69. https://doi.org/10. 1016/S0263-8223(03)00214-93

[19]. Talib, A. A., Ali, A., Badie, M. A., Lah, N. A. C., & Golestaneh, A. F. (2010). Developing a hybrid, carbon/glass fibre-reinforced, epoxy composite automotive drive shaft. Materials and Design, 31(1), 514–521. https://doi.org/10.1016/j.matdes.2009.06.015

If you have access to this article please login to view the article or kindly login to purchase the article

Single Article

	North Americas,UK, Middle East,Europe		India	Rest of world
	USD	EUR	INR	USD-ROW
Online	15	15

ADD TO CART

Options for accessing this content:

If you would like institutional access to this content, please recommend the title to your librarian.
If you already have i-manager's user account: Login above and proceed to purchase the article.
New Users: Please register, then proceed to purchase the article.