Detection and Control of Saturation Level in the Magnetic Core of a Welding Transformer by ANN Detector and PI Controller

S. Rama Subbanna*, Suryakalavarthi, M**
* Research Scholar, Jawaharlal Nehru Technological University, Hyderabad, India.
** Professor, Department of Electrical and Electronics Engineering, Jawaharlal Nehru Technological University, Hyderabad, India.
Periodicity:August - October'2016
DOI : https://doi.org/10.26634/jic.4.4.8232

Abstract

In the paper, an Artificial Intelligence is proposed for detecting and controlling the magnetization level in magnetic core of a Welding Transformer, which is a part of a Middle-Frequency Direct Current (MFDC) Resistance Spot Welding System (RSWS). It consists of an input rectifier, which produces a DC bus voltage, an inverter, a welding transformer, and a fullwave rectifier that is mounted on the output of a transformer. During normal RSWS operation, welding transformer's magnetic core can become saturated due to the unbalanced resistances of both transformer secondary windings and different characteristics of output rectifier diodes, which causes current spikes and over-current protection switch-off of the entire system. In order to prevent saturation of the transformer magnetic core, the RSWS control must detect that the magnetic core is approaching the saturated region and maintains the saturation within optimal limits. The aim of this paper is to present a reliable method for detection and control of magnetic core saturation. Here, an Artificial Neural Network (ANN) is proposed for detecting the current spikes in the primary current and PI controller is used to maintain the saturation within optimal limits. This is achieved by a combined closed-loop control of the welding current and iron core saturation level.

Keywords

Controllers, Detectors, Hysteresis, Fuzzy Logic Techniques, Neural Network Algorithms, Transformers, Welding.

How to Cite this Article?

Subbanna, S. R., and Suryakalavathi, M. (2016). Detection And Control Of Saturation Level In The Magnetic Core of a Welding Transformer by ANN Detector and PI Controller. i-manager’s Journal on Instrumentation and Control Engineering, 4(4), 37-44. https://doi.org/10.26634/jic.4.4.8232

References

[1]. K. Deželak, J. Pihler, G. Štumberger, B. Klopcic and D. Dolinar, (2010). “Artificial Neural Network Applied for Detection of Magnetization Level in the Magnetic Core of a Welding Transformer”. IEEE Transactions on Magnetics, Vol. 46, No. 2, pp. 634–637.
[2]. W. Li, E. Feng, D. Cerjanec, and G. A. Grzazinski, (2004). “A comparison of AC and DC resistance welding of automotive steels”. In Sheet Metal Welding Conf. XI, Sterling Heights, MI.
[3]. A. Canova, G. Gruosso, and B. Vusini, (2007). “Electromagnetic modelling of resistance spot welding system”. In ISEF 2007, XIII Int. Symp. Electromagnetic Fields in Mechatronics, Czech Republic.
[4]. B. M. Brown, (1987). “A comparison of AC and DC resistance welding of automotive steels”. Welding J., Vol. 66, No. 1, pp. 18-23.
[5]. W. Li, D. Cerjanec, and G.A. Grzadzinski, (2005). “A comparative study of single AC and multiphase DC resistance spot welding”. ASME Trans. J. Manuf. Sci. Eng., Vol. 127, No. 3, pp. 583-889.
[6]. B. Klopcic, G. Štumberger, and D. Dolinar, (2007). “Iron core saturation of a welding transformer in a medium frequency resistance spot welding system caused by the asymmetric output rectifier characteristics”. In Conf. Rec. IAS 2007 Annu. Meeting, New Orleans, LA, pp. 2319–2326.
[7]. K. Deželak, B. Klopcic, G. Štumberger, and D. Dolinar, (2008). “Detecting saturation level in the iron core of a welding transformer in a resistance spot-welding system”. J. Magn. Magn. Mater., Vol. 320, No. 20, pp. 878–883.
[8]. K. Deželak, G. Štumberger, B. Klopcic, D. Dolinar, and J. Pihler, (2008). “Iron core saturation detector supplemented by an artificial neural network”. Prz. Elektrotech., Vol. 84, No. 12, pp. 157–159.
[9]. B. Klopcic, D. Dolinar, and G. Štumberger, (2008). “Advanced control of a resistance spot welding system”. IEEE Trans. Power Electron., Vol. 23, No. 1, pp. 144–152.
[10]. D.J. Ramboz, (1996). “Machinable Rogowski coil, design, and calibration”. IEEE Trans. Instrum. Meas., Vol. 45, No. 2.
[11]. J.M. Mendel, (1995). “Fuzzy Logic Systems for Engineering: A Tutorial”. Proc. IEEE, Vol. 83, pp. 345-377.
[12]. J. Pihler, B.Grcar, and D. Dolinar, (1997). “Improved operation of power transformer protection using artificial neural network”. IEEE Trans. Power Del., Vol. 12, No. 3, pp. 1128–1136.
[13]. M. El-Banna, D. Filev, and R.B. Chinnam, (2008). “Online qualitative nugget classification by using a linear vector quantization neural network for resistance spot welding”. Int. J. Adv. Manuf. Technol., Vol. 36, No. 2–4, pp. 237–248.
[14]. G. Shirkoohi, (2015). “Dependence of Magnetization near Saturation on Alloying Content in Ferromagnetic Steel”. IEEE Transactions on Magnetics, Vol. 51, No. 7.
If you have access to this article please login to view the article or kindly login to purchase the article

Purchase Instant Access

Single Article

North Americas,UK,
Middle East,Europe
India Rest of world
USD EUR INR USD-ROW
Online 200 35 35 200 15
Pdf 35 35 200 20
Pdf & Online 35 35 400 25

Options for accessing this content:
  • If you would like institutional access to this content, please recommend the title to your librarian.
    Library Recommendation Form
  • If you already have i-manager's user account: Login above and proceed to purchase the article.
  • New Users: Please register, then proceed to purchase the article.